View and Download Escort A operation manual online. Count Multimeter. A Multimeter pdf manual download. Here you will find a large selection of new and used Escort A listed at special prices. Although some items match several categories, all of them are listed. Section 7. GPIB Remote Operation. Introduction. Description of the GPIB. GPIB Interface Parameters Setup. Commands Summary. 72 .
|Published (Last):||4 January 2004|
|PDF File Size:||15.21 Mb|
|ePub File Size:||13.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
Measuring DC voltage and AC ripple on a rectification circuit. Press to enter Refresh Hold mode. A-2 Technical Specifications Specifications assumptions: LIMit Set and query the comparator. This display shows measuring readings, annunciator, and messages.
Escort 3136A Operation Manual
Page 87 Table Press then followed by to exit percentage function Notes: Use 1 and 2 to distinguish from primary display and secondary display, respectively. It is unnecessary to send complete command characters. The front and rear protective holsters can be removed when mount the meter into a rack.
Page 67 R1 command After executing R1 command, the meter will return the existing readings of primary display. FREQuency [ 2 ] Description: Grounding the Meter The meter is grounded through power cord. Diode Continuity Tests Press to select diode continuity function, then connect the test leads across the diode under test as shown in Figure Reversing the polarity will reverse-bias the diode. Plays an audio ‘beep’ checking that communication is ok mmA beep: When turning the meter on, it assumes its power-up configuration.
This command pauses program execution until all operations are completed. The user must be familiar with the basic measurement operations described in Section 2 and Section 3 and has a basic understanding of electronics knowledge.
By pressing ‘print’ button you will print only current page. It also explains the detail information of all IEEE It is presently not possible to handle more than 1 mmA multimeter per computer.
Page 40 the LO limit value. Sets the brightness of the displays. Related Manuals for Escort A No related manuals.
Escort A used or new for sale at used-line
Do not apply a voltage exceeding V peak between and COM input terminals. Command Syntax Query Commands The purpose of Query commands is used for requesting the meter to respond its current status. Though it is not necessary to read the entire manual to operate the unit effectively, we recommend the manual to be read thoroughly in order to 31336a the meter to its full advantages. Instructions Of Command Sets Escor RS of the meter is under print-only mode, the meter will print out the measured data when the measurement cycle is completed.
The correct fuse ratings: DBM – dBm calculation. Operation Procedures for Front Panel To enable an external trigger and trigger a measurement from the front panel, perform the following procedures: Selecting Trigger Mode once over the maximum display of This function will be used for lock range.
Arithmetic Function Selection 5. Before cleaning this meter, make sure the power is switched in OFF position and the power cord is disconnected from the AC outlet. Enable or disable the auto range mode. Resets the command mode to “local” front end keyboardCloses the serial port communication, and Destroys the related TCL session. Selecting Secondary Display In manual range mode, to select higher range or lower range to the desired one.
The default display is always display 1. Query Commands Query Commands R0 command R0 command is used for requesting the meter to esfort its current status. To display AC voltage in primary display ezcort the frequency in secondary display or vise versus while measuring an AC signal, user may dscort AC voltage and its frequency of an AC Power Supply or circuit by taking a single meter.
It also explains the detail information of all RS interface command rscort used in the meter.
The communication parameters are set to bauds, no parity, 8 databits, 1 stop bit. IEEE interface Optional provides full programmability. Parameters may be numbers, strings or boolean. To avoid personal injury, do not remove the cover or panel. To display DC voltage in primary 31336a, and AC voltage in secondary display or vise versus while testing a rectifier circuit, user may check the DC voltage supplied and its AC ripples by taking a single meter.
You must register and log in before setting up notifications. BUS – Selects a bus command and enter single trigger mode. Overload Alert The meter has provided an overload alert for voltage and current measurements.
The format of printed data will be shown as one of the following: Combination of Dual Display Settings Table provides the available combination of inputs for the primary display and secondary display in the dual display mode.
Page 78 instrument that requested service. Vac and frequency of the input signal you are measuring.